Military Vehicles & Tanks

Centurion Road Wheel rubber replacement. Sufficient for 24 road wheels and two spares, i.e., for one vehicle.This upgrade set is designed as a direct replacement for the AFV Club Centurion rubber wheels. Measurements were directly taken from an Australian Army Centurion Tank, then designed and 3D ..

Extra thin & soft Expandable Only for water-based paints..

Conversion set for Italeri kit. Contains 26 resin parts, and photo-etched sheet..

Contains 11 resi parts. Conversion set for Italeri kit Mercedes L3000..

Conversion kit for the US Sherman tank. The kit contains 68 cast resin parts and 22 parts made on a 3D printer. It includes a sheet of photo-etched parts and detailed assembly instructions. The conversion kit is designed for the Italeri kit Sherman recovery. The kit does not contain glue or paints a..

Conversion kit for the US Sherman tank. The kit contains 68 cast resin parts and 22 parts made on a 3D printer. It includes a sheet of photo-etched parts and detailed assembly instructions. The conversion kit is designed for the Asuka kit US Tank recovery vehicle M32B1. The kit does not contain glue..

Set includes a new T23 Union Steel 'ventless' turret, initial low profile loader 'split hatches' parts and correct 'pyramid' air intake. With some tweaks this set can be adapted eventually to Italeri and Dragon M4A1 and it will be compatible with all recent 3D improvement sets from HD Models.1/35 ..

It can be adapted to Asuka M4A3(76) early kit as well as MENG M4A3(76) early kit. 3 resin parts..

StuG III/IV late type cupola. Comes with the scissor periscope (Scherenfehrnrohr). Highly detailed 3D printed set with maximum realism, detail and intricacy.Fits all market models. Dedicated also for the Beob.Pz.Wg. IV Ausf. J...

StuG III/IV early type cupola. Comes with the scissor periscope (Scherenfehrnrohr). Highly detailed 3D printed set with maximum realism, detail and intricacy.Fits all market models...

The set includes the correct version of the M4A2 Fisher welded upper hull.Tow bar clips are included for early or late positionOLD GARAGE SERIESThe kit contains:6 resin partsmastered by: Fabio Sacchiresin parts to assemble and paint...

1/35 Sherman ARV (Armoured Recovery Vehicle) Mk.II Conversion Set (for Tasca M4A4 kit)..

The product is unassembled and unpainted pure resin conversion set...

2 types of shield, 3D printed..

2 types of shield, 3D printed..

..

..

Lewis MG w/Scarff Mount for RR Armored Cars (all models on the market).Equisit proposition for allied vehicles fans, and the iconic RR armored car. This is one of the two types of mount, we call it type A.Highly detailed 3D printed aftermarket set, comprises of 3 separate parts - turret ring, m..

Contains correct side panels, super detail set for cab, stowage, spare wheels late equipment, resin wheels, PE sand channels and double Browning.303 double guns.Contains over 100 resin and photoetched parts...

The light Feldhaubitzprotze 18 for the light field howitzer 18 - was used for the horse-powered operation of the 10.5 cm light Feldhaubitze 18. The 10.5 cm light Feldhaubitze 18 was developed in the late 1920s and was officially introduced with the AHM 1935, Blatt 18 from 3 August 1935. The light Fe..

#NOTE: The set does NOT include a model kit...

1/35 Churchill ARK (Armoured Ramp Carrier) Mk.I Conversion (Early and Late) (for AFV Club Churchill kit)This is Churchill ARK Mk.I Conversion for AFV Club Churchil Mk.III. Allows you to make an early version with short rear ramps or a late version with long rear ramps. ARKs were made on Mk.II or Mk...

Contains 14 resin and photoetched parts.* NOTE: The Matilda model kit is NOT included in this set...

Basic driver's position for Sherman..