1/72 Wet Decals - Sukhoi Su-24 Fencer
Out Of Stock
Type: water-slide decals
1. Su-24 "Fencer-C" Unit: 735th BAP, Soviet AF. Serial: 10. Karshi airfield. The aircraft equipped with OFAB-250-270.
2. Su-24 "Fencer-C" Unit: 149th GvBAP, Soviet AF. Serial: 40. Crew: Sub.Col.V.A.Markin, Cpt.A.Saveliev. Typical load of FAB-500M-62 bombs. Aircraft of 149th GvBAP flew missions to Afghanistan in 1984 from Kokaidy and Khanabad in 1988-1989.
3. Su-24 "Fencer-C" Unit: 149th GvBAP, Soviet AF. Serial: 42 Karshi airfield, October-December 1988. The aircraft equipped with
FAB-1500M-46 bombs. Aircraft flew missions over Afghanistan.
4. Su-24M Unit: 143rd BAP, Soviet AF. Serial: 20. Kopet-Nari.
5. Su-24 M the air force of Russia, the Krasnodar military of the United flight and technical College, summer 1993. The paint scheme has provided V. P. Pupkov.
6. Su-24M Unit: 455th BAP. Serial: 29. Voronezh, 2002.
7. Su-24M Serial: 44 . 4th trainer centre, Lipetsk, 2002.
8. Su-24MK Serial: 24246. Circa 1991.
9. Su-24MK Unit: 72 Sqn, IRIAF. Serial: 3-6810 Shiraz AB.
10. Su-24MK Serial: KX-88.
11. Su-24M Unit: 455th BAP, 16th VA. Serial: 26 Bunchuk airfield, Voronezh. On 28th April 1998. 45th anniversary on
455th BAP. Note: advertisement stick Pepsi-Cola on the radar cover.
On 29th May 1998 16th VA was disband.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softener is also recommended at this stage. After applying softener, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
1. Su-24 "Fencer-C" Unit: 735th BAP, Soviet AF. Serial: 10. Karshi airfield. The aircraft equipped with OFAB-250-270.
2. Su-24 "Fencer-C" Unit: 149th GvBAP, Soviet AF. Serial: 40. Crew: Sub.Col.V.A.Markin, Cpt.A.Saveliev. Typical load of FAB-500M-62 bombs. Aircraft of 149th GvBAP flew missions to Afghanistan in 1984 from Kokaidy and Khanabad in 1988-1989.
3. Su-24 "Fencer-C" Unit: 149th GvBAP, Soviet AF. Serial: 42 Karshi airfield, October-December 1988. The aircraft equipped with
FAB-1500M-46 bombs. Aircraft flew missions over Afghanistan.
4. Su-24M Unit: 143rd BAP, Soviet AF. Serial: 20. Kopet-Nari.
5. Su-24 M the air force of Russia, the Krasnodar military of the United flight and technical College, summer 1993. The paint scheme has provided V. P. Pupkov.
6. Su-24M Unit: 455th BAP. Serial: 29. Voronezh, 2002.
7. Su-24M Serial: 44 . 4th trainer centre, Lipetsk, 2002.
8. Su-24MK Serial: 24246. Circa 1991.
9. Su-24MK Unit: 72 Sqn, IRIAF. Serial: 3-6810 Shiraz AB.
10. Su-24MK Serial: KX-88.
11. Su-24M Unit: 455th BAP, 16th VA. Serial: 26 Bunchuk airfield, Voronezh. On 28th April 1998. 45th anniversary on
455th BAP. Note: advertisement stick Pepsi-Cola on the radar cover.
On 29th May 1998 16th VA was disband.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softener is also recommended at this stage. After applying softener, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/72 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
- Stock: Out Of Stock
- Reward Points: 20
- SKU: PRS72-184
Print Scale Decals
MRP: US$16.41 Save: US$3.02
18% OFF
US$13.39
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.