Flying Leathernecks

This set includes four (4) missile launchers in medium gray 3D printed resin.Missiles come as shown with print supports removed. Some very minor sanding to smooth areas where supports were located may be necessary.Launchers designed by Richard VanZandt of Flight Line Resin..

These Missile Launchers are designed to fit the Hasegawa F/A-18E/F wing tip and work perfectly with the Meng kit with one small modification to the kit part.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fit..

These Missile Launchers are designed to fit the Hasegawa F/A-18E/F wing tip and work perfectly with the Meng kit with one small modification to the kit part.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fit..

Set includes four (4) launchersUse for early F/A-18E/F..

Set includes four (4) launchersUsed to carry and launch AIM-9X and AIM-120B/C..

Set includes four (4) launchersUse for early F/A-18E/F..

Set includes four (4) missile launchers.Used to carry and launch AIM-9X and AIM-120B/C..

Set includes four (4) launchers.Used to carry two LAU-127E/A or LAU-127A/A for dual AIM-9X / AIM-120B/C carriage..

LAU-115C/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the LAU-115 for carriage of AIM-9 or AIM-120 missiles...

LAU-115/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the LAU-115 for carriage of AIM-9 or AIM-120 missiles. ..

This set includes eight (8) wing pylons, one (1) centerline pylons, and seven (7) BRU-36 ejector racks.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..

This set includes four (4) GBU-12 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the guidance section u..

This set includes two (2) fuel tanks, made up of four (4) parts each. The nose section, main body, tail cone and a key to line up the nose and main body.Lightly sand the forward mating surface of the main body to remove the print support nibs, insert key, then attach nose section. Light sanding of..

3D ResinThis one piece boarding ladder is designed to fit both the Meng and Hasegawa Super Hornet / Growler kits. May also work with the Revell and Italeri kits, with possible modifications to kit needed.Designed by Richard VanZandt of Flightline Resin, item comes as shown in the photo...

Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are four (4) pieces in this set. Second aft strut door is to show antenna detail on outside surface...

Vinyl Mask..

3D ResinThis set includes the following items :Updated and Detailed Instrument Panel for BuNo's 163985 and Up Rudder Pedals GPS Antenna Shark Fin UHF/VHF Antenna Standard Comm Antenna AN/APX-111 IFF Antenna JHMCS Sensor AOA Probes..

Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are six (6) pieces in this set...

Vinyl Mask..

Vinyl Detail..

Cut in holographic vinyl to replicate the windows on the seeker head of the pod. Simply peel and stick after pod has been painted, decaled and weathered. Enough pieces for six pods are included.For the Hasegawa and Kinetic F/A-18A/B/C/D kits..

Designed to be used with the Hasegawa kits, this is a simple to use and inexpensive way to replicate the strap applied to the bottom of the fuselage...

3D ResinThis set includes three (3) pieces that make up the belly strap found on late F-4E and all F-4G Phantoms. Designed to be used on the Meng kits, it may work with other kits with some adjustments.The strap was also found on the F-4S and the F-4J's operated by the UK.Parts come as shown a..

This is a pre-cut vinyl mask set designed to be used with the new Tamiya F-4B. While the kit does include masks, they are on one continuous sheet. Our set is a good time saver and will help avoid mistakes while cutting around the printed lines on the kit set...