Print Scale 72-144 1/72 Wet Decals - Fiat G.50 Freccia (1 sheet)

Type: water-slide decals
1. Fiat g. 50 part: 3./jagdgeschwader 108 number: 352 Wiener-Neustadt, 1944.
2. Fiat G.50 bis Part: 352 Squadriglia Phone: 352-2 (MM8978) Libya, 1941.
3. Fiat G.50 bis Part: 352 Squadriglia, 20 Gruppo, 51 Stormo Phone: 352-7 AFB Maldegem, Belgium, Fall 1940.
4. Fiat G.50 Part: 155 Gruppo Autonomo Phone: 351-12 April 1941.
5. Fiat G.50 Part: 20 Gruppo, CAI Phone: 20 (MM5372) Belgium, November 1940 The aircraft carries a typical Italian G.50 camouflage. By car flew commander of the 20th Group Mario Bonsai. The group was part of the Italian Corps, which operated in the neighborhood of La Mashnov winter 1940/1941.
6. Fiat G.50bis Part: 356 Squadriglia, 151 Gruppo Number: 366 Greece, 1942.
7. Fiat G.50 Serie 1 Part: unknown Phone: MM3590 So the plane looked before sending the unit. The aircraft carries the standard camouflage applied at the factory: the upper and side surfaces of the Giallo Mimetico 3 (FS 33434) spotted Verde Mimetico 3 (FS 34102), the lower surface Grigio Mimetico (FS 36293).
8. Fiat G.50 Part of: Grupo 27, Regimiemto Mixto de Africa Espagnol Phone: 1-7 (MM3582) Melilla, Morocco, 1940.
9. Fiat G.50B Serie VII Part: 21.LJ, 11.LS (Lovacka Skupina) No. 3510 Borongay, Zagreb, Croatia, the beginning of 1944.
10. Fiat G.50bis Part 12 Lovacko Jato No. 3502 Of 1942-1943.
11. Fiat G.50bis Number: 8 (c / n.249, MM6197, ex-Croat AF No.3505)
Former Croatian plane captured guerrillas.
12. Fiat G.50 (2nd series) Part 1 / LeLv 26 Number 2 (FA-15, c / n.4706) Aerodrome Lunkula, June 1941 On the first aircraft
of the second series was kept vertical tail early sample.
13. Fiat G.50 Part 1 Gruppo Sperimentale Caccia Aviacion Legionaria No. 1-2 (3586)
14. Fiat G.50 Part 1 Gruppo Sperimentale Caccia Aviacion Legionaria Number: 1-1 Pilot - the commander of the Italian experimental group, Major M.Bonzano. Spain, March 1939.
15. Fiat G.50 bis of 376 Squadriglia, 154 Gruppo Autonomo C.T., Regia Aeronautica. Berat Greece, November 1940.

How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.