Model Planes

These are 3D printed face curtain handles for MB Phantom ejection seats. The handles are mainly designed for the Hypersonic Models Mk. H5 seats but can be used on other types (H7) and manufacturer's seats as well. The handles are 3D printed but from a slightly elasctic resin that doesn't break as ea..

This is an empty SR-71 brake chute bay with open doors, as commonly seen after landing. Designed specifically for the Revell kit. The set comes in four 3D printed parts: the main bay, a separate end cap (for easier painting) and separate doors. The door parts have mounting lips and recesses designed..

This set contains the parts needed to build an accurate late type F-104A from the Kinetic F-104A/C kit. "Late" means that it's an airframe that was converted to the upward firing C-2 seat. Therefore you can either use the kit supplied seat or one of the various available aftermarket options.The pa..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

This is a set of two aft canopy braces for Kinetic F-104 Starfighter kits. This part is applicable to all F-104 single seat variants and is not provided in any of the Kinetic's kits. The part is very delicate, but printed from slightly forgiving resin for safer support removal and handling...

..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

..

..

This is a replacement resin fin tip for the HobbyBoss Intruder family. The HB fin tip has the wrong shape and once you have noticed the error you can't ignore it any longer...the surface detail is slightly corrected and enhanced as well. The required cut on the kit is fairly simple as it's along a p..

This is a backdate set for the (new tool) Kinetic F-16A kit and contains parts to build Block 1,5 and 10 aircraft. The set includes small stabilators with thin static wicks, early instrument panel and coaming, Environment Control System (ECS) exhaust panel, RWR and rectancular UHF antennas. The stab..

A set of two Martin Baker Mk. H5 ejection seats for early F-4B, F-4C and F-4D Phantoms (until around 1970). Suitable for and tested with Academy, Hasegawa and Zoukei Mura kits. The seats have cast on seat belts which differ from each other...

This is a set of corrected engine nacelles with intakes, exhausts and pylons for the Trumpeter A-3 Skywarrior kits in 1:48. Suitable for all variants. This set also includes parts that enable the modeller to build the kit with dropped flaps. Please note that the first print run of the instructions m..

Dewoitine D.520, No.73/10 flown by Adj Andre Carrier of 2 Escadrille, GC I/3 Armee de L'Air, Wez-Thuizy, May 1940. The pilot lost his life in this aircraft on 14 May 1940...

Dewoitine D.520 with 1AC. 1AC fought the Allies during the Syria-Lebanon campaign...

1. Convaiir F-102A Delta Dagger 61144, serving with 95th FIS at Andrews AFB, Maryland, 1958. Overall Gloss Grey with black radome.2. Convaiir F-102A Delta Dagger 61103, serving with 86th Fighter Interceptor Youngstown Municiple Airport, Ohio, 1957-1960. Overall Gloss Grey With black radome.3. Co..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Water-slide Decals: Instruction: 1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2. Cut out the decal you need (do it on cutting mat) 3. Grab the d..

Type: water-slide decals1. Beaufighter 21 A8-27 DU-A ?Reckabye Baby?, flown by the crew of F/L McMilan & F/O Hayes of no. 22 Sqn RAAF, based at Morotai in February 19442. Beaufighter If, X7716/A, No. 89 Squadron 3. Beaufighter VIf, ND243/Q, No. 46 Squadron Gambit, Libya, September-October 1944 How ..

Type: water-slide decals1. P-400 of 39 FS, 35 FG, 5 AF, 12 Mile Aerodrome New Guinea, 1942, personal aircraft of Lt. Eugene Wahl.2. P-39D-I(41-28297) ?51" of 363rd Training Squadron California 1942.3. P-39D-I (41-38350) ?P" of 35 FS, 8 FG, 5 AF, Milne Bay, New Guinea, October 1942. Personal aircraft..

This is a set of 3D printed B-26K (A-26A) Counter Invader / Nimrod wheels. For the ICM kit in 1:48. The mounting points are designed for a direct fit to the kit axles. The wheel hubs are loaded with fine and accurate detail, from valve stems to visible springs in the brake pads. The tyres have very ..

Vehicles equipped with this radar F-4J Phantom II F-4J(UK) Phantom II F-4S Phantom II Phantom FG.1 Phantom FGR.2..

..