Model Planes

In February of 1964, the LAU-7A/A was introduced as a USAF version of the LAU-7/A that incorporated provisions for launching the TDU-11/B Target Rocket.The LAU-7A/A was used interchangeably with the Aero-3B on USAF F-4C/D/E Phantoms.The standoff adapters in this set are designed to fit the Zouke..

In January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6.Over the course of the next several years, numerous AAC's changed the designation of the launcher to B/A, A-7, B/A-1, as well as a few others. However, all of these changes were either..

This set includes four (4) empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y, A-10, F-16 and a number of other aircraft.Rocket tubes are hollow the entire length of the pod to dep..

Designed by Petr Haupt, this set includes two (2) LAU-33 Pods, four (4) Mk-71 Rocket Motors, four (4) Mk32 Mod 0 anti tank / anti personnel warheads with Mk188 Impact Fuzes and four (4) Mk32 Mod 0 warheads with Mk93 proximity fuzes..

This set includes four (4) missile launchers in medium gray 3D printed resin.Missiles come as shown with print supports removed. Some very minor sanding to smooth areas where supports were located may be necessary.Launchers designed by Richard VanZandt of Flight Line Resin..

These Missile Launchers are designed to fit the Hasegawa F/A-18E/F wing tip and work perfectly with the Meng kit with one small modification to the kit part.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fit..

These Missile Launchers are designed to fit the Hasegawa F/A-18E/F wing tip and work perfectly with the Meng kit with one small modification to the kit part.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fit..

Set includes four (4) launchersUse for early F/A-18E/F..

Set includes four (4) launchersUsed to carry and launch AIM-9X and AIM-120B/C..

Set includes four (4) launchersUse for early F/A-18E/F..

Set includes four (4) missile launchers.Used to carry and launch AIM-9X and AIM-120B/C..

Set includes four (4) launchers.Used to carry two LAU-127E/A or LAU-127A/A for dual AIM-9X / AIM-120B/C carriage..

LAU-115C/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the LAU-115 for carriage of AIM-9 or AIM-120 missiles...

LAU-115/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the LAU-115 for carriage of AIM-9 or AIM-120 missiles. ..

Vinyl Mask..

This set includes eight (8) wing pylons, one (1) centerline pylons, and seven (7) BRU-36 ejector racks.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..

Photo etched stainless steel..

This set includes four (4) GBU-12 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the guidance section u..

This set includes two (2) fuel tanks, made up of four (4) parts each. The nose section, main body, tail cone and a key to line up the nose and main body.Lightly sand the forward mating surface of the main body to remove the print support nibs, insert key, then attach nose section. Light sanding of..

3D ResinThis one piece boarding ladder is designed to fit both the Meng and Hasegawa Super Hornet / Growler kits. May also work with the Revell and Italeri kits, with possible modifications to kit needed.Designed by Richard VanZandt of Flightline Resin, item comes as shown in the photo...

Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are four (4) pieces in this set. Second aft strut door is to show antenna detail on outside surface...

3D ResinThis set includes the following items :Updated and Detailed Instrument Panel for BuNo's 163985 and Up Correct and Detailed WSO Instrument Panel for BuNo's 163986 and Up Correct WSO Instrument Panel Cover for the F/A-18D Left and Right side console WSO Control Sticks Rudder Pedals x 2 GPS A..

Vinyl Mask..

3D ResinThis set includes the following items :Updated and Detailed Instrument Panel for BuNo's 163985 and Up Rudder Pedals GPS Antenna Shark Fin UHF/VHF Antenna Standard Comm Antenna AN/APX-111 IFF Antenna JHMCS Sensor AOA Probes..