Model Planes

3D Scanned & Designed 9 Resin Parts / Optional 2 Heads..

3D Scanned & Designed 9 Resin Parts / Optional 2 Heads..

3D Scanned & Designed7 Resin Parts..

3D Scanned & Designed20 Resin PartsOptional 4 Heads..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Type: water-slide decals1. SPAD Xll Charles J Biddle, commander of the 13th Aero Sguadron.It is shown here undergoing ground testing in October 19182. Spad XIII S 15202 of Lt Frank LukeJr, 27th Aero Sguadron, September 19183. Spad XIII S15137 of Lt David E Putnam139th Aero Sguadron, september 19181/..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

This is a full-length resin exhaust and nozzle set with the specific detail for EA-6B Prowlers which have an upgraded engine and different nozzle to the A-6 Intruder family. The instructions are based on fitting it to the Kinetic/Italeri kits, but the modeller may be able to adapt them to the Revell..

Including 2 seats 6 Resin, 14 PE parts..

for AFV Club 14 Resin/ 15 PE parts..

Type: water-slide decals1. F-86E-1-NA 50-623 ?Pretty Mary? of the 335th FIS / 4th FIW flown by Col. Harrison R. Thyng.2. F-86E-10-NA 51-2738 ?Father Dan? 25th FIS / 51st FIW flown by 2nd Lt. Sam P. Young.3. F-86F-10-NA 51-12958 ?The Paper Tiger? of the 39th FIS / 51st FIW flown by Capt. Harold E. Fi..

..

The is a strike camera chin pod for the nose of the Zoukei Mura F-4C. This pod was used for example by Col Robin Olds on Operation Bolo. Later, many of these chin pods were re-fitted with forward RHAW pods, retaining only the rearward facing camera. Included in this set are two types of front ends -..

This is an early, plain fin cap without any RHAW or ECM pods as used on early F-4B (and C). Designed as a drop in replacement part for the Tamiya kit...

F-4 Phantom C/L pylon, 1:48, for the Zoukei Mura line of kits. The pylon fit on and into the detail moulded onto the ZM lower wing surface. It comes with two sets of separate pins - one for the larger stabiliser pins and the smaller sway brace pins that connect to the stores to be mounted...

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

F-4 Phantom C/L pylon, 1:48, for the Tamiya line of kits. The pylon fits on and into the moulded-on mounting tab between the Aux doors on Tamiya's kit with a simple modification (it needs to be shortened and slightly re-shaped). The pylon set comes with two sets of separate pins - one for the larger..

Decals for F-15E that took part in the operation Odyssey Dawn, Libya 2011. Features two aircraft, 97-0219 and 01-2003. Markings include full crew names that were re-applied after the operation, full contemporary stencils and landing gear placards. The set comes with paint masks for insignia, ID mark..

Hollowed, thin-walled resin part to detail the open-ended Jet Fuel Starter (JFS) exhaust tubing as found on modern Eagles, such as the F-15C and F-15E Strike Eagle. A small part that adds detail and interest to this area and brings it up to date on all 1:48 F-15 kits...

These are 3D printed face curtain handles for MB Phantom ejection seats. The handles are mainly designed for the Hypersonic Models Mk. H5 seats but can be used on other types (H7) and manufacturer's seats as well. The handles are 3D printed but from a slightly elasctic resin that doesn't break as ea..

This is an empty SR-71 brake chute bay with open doors, as commonly seen after landing. Designed specifically for the Revell kit. The set comes in four 3D printed parts: the main bay, a separate end cap (for easier painting) and separate doors. The door parts have mounting lips and recesses designed..

This set contains the parts needed to build an accurate late type F-104A from the Kinetic F-104A/C kit. "Late" means that it's an airframe that was converted to the upward firing C-2 seat. Therefore you can either use the kit supplied seat or one of the various available aftermarket options.The pa..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..