Model Planes

..

Paint Mask:Preparing the masks: Masks should not be stretched during the application process as they are flexible and this could cause deformation. Remove the whole mask if necessary, and then apply again. Once placed on the model, the mask surface should be adjusted to the surface of the model ..

This is a plastic model kit, which comes unassembled and unpainted. So glue, model paints and other basic modelling tools are additionally required...

The set includes turned aluminum barrels and etched rings.It is very simple to use in Your model, and makes it extremely realistic. Insert the metal parts using Cyanoacrylate adhesives...

..

The set includes turned brass barrels.It is very simple to use in your model, and makes it extremely realistic. Simply cut off the original plastic barrel and drill a hole in the remaining plastic parts and insert the metal barrel using Cyanoacrylate adhesives...

The set includes turned brass barrels.It is very simple to use in Your model, and makes it extremely realistic. Simply cut off the original plastic barrel and drill a hole in the remaining plastic parts and insert the metal barrel using Cyanoacrylate adhesives...

The set includes turned brass barrels and blast tubes.It is very simple to use in Your model, and makes it extremely realistic. Simply cut off the original plastic barrel and drill a hole in the remaining plastic parts and insert the metal barrel using Cyanoacrylate adhesives.Mounting Position: (See..

The set includes turned brass barrels with drilled cooling jackets and blast tubes.Simply cut off the original plastic barrel and drill a hole in the remaining plastic parts and insert the metal barrel using Cyanoacrylate adhesives.Product Features:- Drill proper holes for 0.50 cal browning diameter..

This is a replacement resin fin tip for the HobbyBoss Intruder family. The HB fin tip has the wrong shape and once you have noticed the error you can't ignore it any longer...the surface detail is slightly corrected and enhanced as well. The required cut on the kit is fairly simple as it's along a p..

** This model kit is supplied in unassembled and unpainted plastic components. Please note that glue, model paints, and other basic modelling tools are required and sold separately...

Products made in 3D are not assembled or painted, and there may be colour differences depending on the resin...

..

Fit perfectly to HobbyBoss and Dragon model of German aircraft Me 262 A-1a/U4.Used also in Me 410 A-1/U4The set includes turned aluminum and brass barrel. It is very simple to use in Your model, and makes it extremely realistic. Simply cut off the original plastic barrel and drill a hole in the rema..

Laser cut craft paper kit..

..

..

..

This is a backdate set for the (new tool) Kinetic F-16A kit and contains parts to build Block 1,5 and 10 aircraft. The set includes small stabilators with thin static wicks, early instrument panel and coaming, Environment Control System (ECS) exhaust panel, RWR and rectancular UHF antennas. The stab..

The set includes turned brass Pitot Tube.It is very simple to use in Your model, and makes it extremely realistic. Simply cut off the original plastic barrel and drill a hole in the remaining plastic parts and insert the metal barrel using Cyanoacrylate adhesives. (See Instruction)..

This is a corrected nose intake part for the Kitty Hawk FJ-3 Fury kit. It is a drop-in replacement for the kit part and features a corrected nose profile, in particular around the upper lip where the small radome is located. The kit part is too blunt, in the same way as the FJ-2 part is. The panel l..

This is a cockpit set for Kitty Hawk's FJ-3 Fury kit (1:48). It includes a corrected and detailed seat with parachute and harness in place (which differs from the FJ-2 seat in several details), a detailed rear cockpit bulkhead and turtle deck, the FJ-3 specific antenna assembly (3D printed part) as ..

This is a replacement nose landing gear strut for Kitty Hawk's FJ-2 and FJ-3 Fury kits. It is 3D printed in one piece in strong resin and corrects the misshapen kit part. A lot of detail has been added and refined and as such the item is both a significant upgrade over the kit part as well as an evo..

This is a replacement nose landing gear strut for Kitty Hawk's FJ-2 and FJ-3 Fury kits. It is 3D printed in one piece in strong resin and corrects the misshapen kit part. A lot of detail has been added and refined and as such the item is both a significant upgrade over the kit part as well as an evo..