Flying Leathernecks

Vinyl Mask..

3D ResinThis set includes the following items :Updated and Detailed Instrument Panel for BuNo's 163985 and Up Rudder Pedals GPS Antenna Shark Fin UHF/VHF Antenna Standard Comm Antenna AN/APX-111 IFF Antenna JHMCS Sensor AOA Probes..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are six (6) pieces in this set...

Vinyl Mask..

3D ResinThis is a simple tool that can be used over and over.If built as designed, the vertical tails in the Hasegawa 1/48 Hornets angle too far out. This jig helps set them at the correct angle.Simply score (do not cut off) the outside surface of the locating tabs on the tail parts where it me..

All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..

All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..

Vinyl Detail..

Cut in holographic vinyl to replicate the windows on the seeker head of the pod. Simply peel and stick after pod has been painted, decaled and weathered. Enough pieces for six pods are included.For the Hasegawa and Kinetic F/A-18A/B/C/D kits..

Designed to be used with the Hasegawa kits, this is a simple to use and inexpensive way to replicate the strap applied to the bottom of the fuselage...

3D ResinThis set includes three (3) pieces that make up the belly strap found on late F-4E and all F-4G Phantoms. Designed to be used on the Meng kits, it may work with other kits with some adjustments.The strap was also found on the F-4S and the F-4J's operated by the UK.Parts come as shown a..

This is a pre-cut vinyl mask set designed to be used with the new Tamiya F-4B. While the kit does include masks, they are on one continuous sheet. Our set is a good time saver and will help avoid mistakes while cutting around the printed lines on the kit set...

*** NOTE *** This sheet does NOT include the mask for the bat!Waterslide Decals printed by Microscale (Insert printed by Cartograf).5.5 x 8.5 inch sheet..

Redesigned set includes the plates added to the upper wing and forward nose section. Parts adjusted to accurately fit all 1/48 F-16 kits...

Canopy, wheel mask for GWH kit..

This set includes two (2) main and two (2) nose wheels for Kinetic's 1/48 EA-6B, E-2C and C-2A kits.Due to variations in the printing process, as well as very slight differences in the kits landing gear, it may be necessary to enlarge the mounting holes on each wheel using a small drill bit.Whee..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 5.5 x 8.5 inch sheet..

Vinyl Mask..

This set includes four (4) octagon shaped drip pans commonly found under aircraft, both on the flightline and in hangar spaces. Great for use in dioramas to add a little bit more realism to your scene.Parts come as shown in photo. Very light sanding needed on one surface needed prior to painting...

This set includes masks for all cockpit and cabin windows, as well as wheel masks...

Vinyl Mask..

This set includes six (6) SATCOM Antenna with short mount found on a number of Helicopters. Use fine sprue cutters to remove part from support and lightly sand base smooth. Attach using super glue (CA)...