Model Planes

This set contains six (6) Mk-82 500lb bombs with thermal protective coating and BSU-86 retarded fins. Also included are six (6) each of the following:M904 Nose FuzeMk-43 TDDMXU-735 Solid Nose PlugBombs come as shown in the photo. Light sanding may be needed on the aft end of the tail section..

This set contains six (6) Mk-82 500lb bombs with BSU-86 retarded fins. Also included are six (6) each of the following:M904 Nose FuzeMk-43 TDDMXU-735 Solid Nose PlugBombs come as shown in the photo. Light sanding may be needed on the aft end of the tail section to remove remnants of support ..

This set includes six Mk-82 / BLU-111/B bombs with BSU-33/B tail fins, and six each of the following : M904 nose fuzes, Mk-43 TDD, MXU-735 nose plugs.Accurately reproduced using personal measurements and photos of the real item. Parts come as seen in the photo, leaving minimal work for the modeler..

This set includes six (6) Mk-77 Fire Bombs.Light sanding to remove print support nibs is necessary on the aft end of the bomb..

This set includes twelve (12) Mk-76 25 lb Practice Bombs..

Set of four (4) 3D printed launchersIn February of 1964, the LAU-7A/A was introduced as a USAF version of the LAU-7/A that incorporated provisions for launching the TDU-11/B Target Rocket.The LAU-7A/A was used interchangeably with the Aero-3B on USAF F-4C/D/E Phantoms.The standoff adapters in ..

Set of four (4) 3D printed launchersIn September of 1976, AAC 688 introduced a new dual Fin Retaining Clip for the new AIM-9L Sidewinder, creating the LAU-7/A-4.In June of 1980, AAC-736 was introduced and the launcher became the LAU-7/A-5.The LAU-7/A-5 was the launcher used when two VF-41 F-14..

Set of four (4) 3D printed launchersIn May of 1969, AAC 545 introduced the Fin Retaining Clip for the AIM-9D/G/H Sidewinder, creating the LAU-7/A-1.In January of 1971, AAC-537-1 introduced the Detent Holdback Pin, creating the LAU-7/A-2.By 1972, the launcher was re-designated as the LAU-7/A-3 ..

Set of four (4) 3D printed launchersThe LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.Our sincere thanks to Gerry Whiteside and Bill Arndt for their ass..

Set includes six (6) Mk-82/BLU-111 bombs with KMU-572 tail assemblies and nose strakes attached.Also included are six (6) DSU-33 proximity fuzes, six (6) MXU-735 solid nose plugs and six (6) Ogive nose plugs...

Set includes six (6) Mk-83/BLU-110 bombs with KMU-559 guidance kit and tail assemblies attached.Also included are six (6) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies caused by the oval configuration.This set includes two hollow tanks that require assembly. Some li..

Set FL172-2001 contains four correct SUU-63C/A wing pylons and one correct SUU-62C/A centerline pylon for the F/A-18A++, C and D.These pylons are correct for F/A-18C and D aircraft with BuNo's 163985 thru 165532 and aircraft upgraded to F/A-18A++ standard. The F/A-18A++ can be easily identified by..

Vinyl..

This set includes two (2) XM158A1 Rocket Launchers.The Launcher was a seven-tube, reloadable, reusable, repairable 2.75" rocket launcher M158A1 was a variant of the M158 that included a modified hardback mount..

This is a two piece 3D printed set of the SATCOM antenna mounted to the top of the main rotor mast on the UH-1Y Helicopter. Designed for the Kittyhawk kit.Simply glue the antenna to the top center of the base, paint and attach to your model. Parts come ready to install with no clean up required...

This set includes six (6) cluster bombs and come as shown in the photo.CAD by P. Haupt..

This set contains two (2) PMBR's in an 'unloaded' configuration. Due to the fragile nature of some of the components, the PMBR comes attached to the print supports. Use a fine tipped sprue cutter to carefully remove the supports from the parts.Used on the A-4 and TA-4 Skyhawk, OV-10 Bronco, P-3 Or..