Model Planes

This set includes two (2) XM158A1 Rocket Launchers.The Launcher was a seven-tube, reloadable, reusable, repairable 2.75" rocket launcher M158A1 was a variant of the M158 that included a modified hardback mount..

This is a two piece 3D printed set of the SATCOM antenna mounted to the top of the main rotor mast on the UH-1Y Helicopter. Designed for the Kittyhawk kit.Simply glue the antenna to the top center of the base, paint and attach to your model. Parts come ready to install with no clean up required...

This set includes the following :Six (6) Thermally Protected Mk-82 500lb bombs with Conical FinsSix (6) M904 Nose FuzesSix (6) MXU-735 Solid Nose PlugsSix (6) Mk-43 TDD Proximity Fuzes (not shown)This bomb/fin configuration is correct for use from Vietnam to Desert StormBombs come as sho..

Mk-77 Fire Bombs, set of four (4)Items are 3D printed and come ready to paint. Some very light sanding of the forward section may be necessary to remove remnants of printing supports.Simply paint natural aluminum and install!..

This set includes four (4) LAU-7/A-6 AIM-9 launchers designed to fit the pylons in the ZM F-4S. Used from 1988 to 1991..

This set includes four (4) launchers designed to fit the Tamiya F-4 wing pylons in anticipation for later variants. This launcher was used from 1976 to 1987..

This set includes four (4) missile launchers designed to fit the Tamiya F-4B and were used from 1958 to 1968..

This set includes two (2) LAU-10 rocket pods, eight (8) Mk-71 Mod 1 Rocket Motors, eight (8) Mk-32 Mod 0 AT/AP Warheads with Mk-93 Mod 0 Fuze and eight (8) Mk-32 Mod 0 AT/AP Warheads with Mk-188 Impact FuzesLAU-10 CAD by Matt FarrowRockets and warhead CAD by Dave Roof..

Set includes two (2) Thermally Protected Mk-83/BLU-110 bombs with KMU-559 guidance kit attached and the tail assemblies as separate pieces.Also included are two (2) DSU-33 proximity fuzes, two (2) MXU-735 solid nose plugs and two (2) Ogive nose plugs...

The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies caused by the oval configuration.This set includes two hollow tanks that require assembly. Some li..

Wheels designed to fit the Kinetic F/A-18A/B/C/D Hornet Kits..

3D ResinThis set contains one (1) Right Handed AN/AAQ-28 LITENING Pod in the stowed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

The AERO-3B missile launcher was designed to be used with the AIM-9B Sidewinder missile.This set includes 4 launchers with standoff adapters designed to be used on the Zoukei-Mura F-4C/D/E.Each launcher is 3D printed and come removed from the print supports. All that is needed is a light sandin..

Set FL48-8014 contains four correct SUU-63A/A wing pylons and one correct SUU-62A/A centerline pylon for the F/A-18A+, A++, C and D.Each set also includes five (5) unlocked BRU-32's and five (5) locked BRU-32's to more accurately depict the different configurations with or without ordnance loaded...

Set FL48-8013 contains four correct SUU-63/A wing pylons and one correct SUU-62/A centerline pylon for the F/A-18A and F/A-18B.Each set also includes five (5) unlocked BRU-32's and five (5) locked BRU-32's to more accurately depict the different configurations with or without ordnance loaded.Th..

Set of four (4) 3D printed launchersThe LAU-7F/A was first introduced in 2008, with more widespread use by 2010. This version is used primarily on USMC F/A-18C/D aircraft...

These Missile Launchers are designed to fit the Trumpeter F/A-18E/F wing tip and should work with the Revell kit.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fits into slot on both kit wing tip parts.Fou..

3D ResinThis set contains one (1) Left Handed AN/AAQ-28 LITENING Pod in the stowed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

This set contains four correct SUU-63A/A wing pylons and one correct SUU-62A/A centerline pylon for the F/A-18A+, A++, C and D.These pylons are correct for F/A-18A+ thru D aircraft with BuNo's 163427 thru 163782.This set of pylons corrects the inaccurately shaped pylons included in the Academy k..

3D printed exhaust stacks recommended for Wasp kit...

..

3D printed rocket pod recommended for CM.175 Zephyr, MB326, MB339, CM.170 Magister, etc. kits..

..

..