Model Planes
Brand: Flying Leathernecks
SKU: FL172-2012
Set includes six (6) Mk-83/BLU-110 bombs with KMU-559 guidance kit and tail assemblies attached.Also included are six (6) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...
US$11.79
Brand: Flying Leathernecks
SKU: FL172-2053
The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies caused by the oval configuration.This set includes two hollow tanks that require assembly. Some li..
US$11.79
Brand: SBS Model
SKU: SBS72085
3D printed resin. Comes on printing supports which need to remove...
US$12.97
20 % OFF
US$10.34
Brand: Flying Leathernecks
SKU: FL172-2001
Set FL172-2001 contains four correct SUU-63C/A wing pylons and one correct SUU-62C/A centerline pylon for the F/A-18A++, C and D.These pylons are correct for F/A-18C and D aircraft with BuNo's 163985 thru 165532 and aircraft upgraded to F/A-18A++ standard. The F/A-18A++ can be easily identified by..
US$11.79
Brand: Flying Leathernecks
SKU: FL172-2056
This set includes correctly shaped and sized LEX Fence parts applicable to all 1/72 F/A-18A/B/C/D Hornet kits...
US$7.39
Pre-Order
Brand: Flying Leathernecks
SKU: FL172-2061
Set of 16 correctly sized and shaped pitot tubes for use on the Legacy F/A-18, F-14, A-7, F-8, AV-8B and several other aircraft that use this style of pitot tube.3D printed and lightly supported for easy removal from block...
US$7.39
Pre-Order
Brand: Flying Leathernecks
SKU: FLV72003
Designed to be used with the Hasegawa kits, this is a simple to use and inexpensive way to replicate the strap applied to the bottom of the fuselage. Should also work with Fujimi and Revell Phantom kits...
US$6.20
Brand: Flying Leathernecks
SKU: FLV72001
Redesigned set includes the plates added to the upper wing and forward nose section. Parts adjusted to accurately fit all 1/72 F-16 kits...
US$6.20
Pre-Order
Brand: Flying Leathernecks
SKU: FL172-2014
Designed by Craig Sargent, this piece corrects the misshaped nose on the Hasegawa 1/72 scale kit. This is a direct replacement for the kit parts with minimal clean up required.Part comes as shown in photo..
US$9.75
Pre-Order
Brand: Flying Leathernecks
SKU: FL172-2063
Designed by Richard VanZandt, this set includes 10 pylons.There are two options for the outboard wing pylons. One set has the BRU-36 ejector rack for loading ordnance, and the second set has the adapter for use with the LAU-7 (use FL172-2042).Designed for use with the Hasegawa kit, they should w..
US$11.79
Pre-Order
Brand: Flying Leathernecks
SKU: FL172-2002
The FMV Mod fitted to the tail boom of the AH-1Z and UH-1Y allows grounds units to see what the aircrew sees through the aircraft's FLIR.Designed for the Dream Model AH-1Z kit..
US$6.20
Brand: Flying Leathernecks
SKU: FL172-2004
Designed by Jason Liang, this new set corrects the horribly inaccurate TSS provided in the kit.Modification of the kit part will be needed to use this item...
US$6.20
Pre-Order
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8038
Set of four (4) 3D printed launchersIn September of 1976, AAC 688 introduced a new dual Fin Retaining Clip for the new AIM-9L Sidewinder, creating the LAU-7/A-4.In June of 1980, AAC-736 was introduced and the launcher became the LAU-7/A-5.The LAU-7/A-5 was the launcher used when two VF-41 F-14..
US$9.75
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8037
Set of four (4) 3D printed launchersIn May of 1969, AAC 545 introduced the Fin Retaining Clip for the AIM-9D/G/H Sidewinder, creating the LAU-7/A-1.In January of 1971, AAC-537-1 introduced the Detent Holdback Pin, creating the LAU-7/A-2.By 1972, the launcher was re-designated as the LAU-7/A-3 ..
US$9.75
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8036
Set of four (4) 3D printed launchersThe LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.Our sincere thanks to Gerry Whiteside and Bill Arndt for their ass..
US$9.75
Brand: Flying Leathernecks
SKU: FL48-8140
3D ResinThis set includes twenty four (24) USAF style solid nose plugs These are designed to work with all kit supplied bombs that may not have accurate or clean versions...
US$7.39
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8109
3D ResinThis set includes six (6) highly detailed and accurate IFR probe tips for use on all US and NATO aircraft that use the hose and drogue system...
US$7.39
Pre-Order
Brand: Flying Leathernecks
SKU: FLM48-30
Canopy and wheel mask for Gallery / Trumpeter kits..
US$6.20
Brand: Flying Leathernecks
SKU: FL48-8009
This is a two piece 3D printed set of the SATCOM antenna mounted to the top of the main rotor mast on the UH-1Y Helicopter. Designed for the Kittyhawk kit.Simply glue the antenna to the top center of the base, paint and attach to your model. Parts come ready to install with no clean up required...
US$7.39