Model Planes

..

..

..

..

..

..

1. F-86A 5 NA, 49 1289, 92 nd Fighter Interceptor Squadron, 81 st Fighter Interceptor Wing, flown by Lt. Col. Jim Carlyle, RAF Shepherds Grove, August 1951.2. F-86A 5 NA, 49 1028, ''Texas Tailpipe'', 56 th Fighter Group (Air Defense), flown by Col. Robert Case y , Orchard Place AFB (now Chicago O'..

Paint Mask:Preparing the masks: Masks should not be stretched during the application process as they are flexible and this could cause deformation. Remove the whole mask if necessary, and then apply again. Once placed on the model, the mask surface should be adjusted to the surface of the model ..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

  Brand New 1:48 Model Manufacturer: Tamiya Item No.12624   The pitot tube is made of stainless s..

Type: water-slide decals1. MiG-19 PM, a board 335. Museum of the Air Forces of GDR, Berlin-Gatov.1980.2. Mikoyan/Gurevich MiG-19 ?24 red? of the 33rd IAP based at Wittstock AB was flown by Capt. Fyodor Zinov?yev against the RB-66 which intruded into East German airspace on 10th march 1964. The plan ..

Type: water-slide decals1. 2nd figher-bombing squadron. Port-Harkort, Nigeria, 1969 NAF612 served in 2nd figter-bombing a squadron and concerned the second party MiG-17F (NAF611 - NAF614), received in April, 1968 from the USSR through Poland. The plane initially hasn't been painted, but already bore..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Vehicles equipped with this radar F-4J Phantom II F-4J(UK) Phantom II F-4S Phantom II Phantom FG.1 Phantom FGR.2..

..

..

..

..

..