All Products

This is a backdate set for the (new tool) Kinetic F-16A kit and contains parts to build Block 1,5 and 10 aircraft. The set includes small stabilators with thin static wicks, early instrument panel and coaming, Environment Control System (ECS) exhaust panel, RWR and rectancular UHF antennas. The stab..

The set includes turned brass Pitot Tube.It is very simple to use in Your model, and makes it extremely realistic. Simply cut off the original plastic barrel and drill a hole in the remaining plastic parts and insert the metal barrel using Cyanoacrylate adhesives. (See Instruction)..

..

..

This is a corrected nose intake part for the Kitty Hawk FJ-3 Fury kit. It is a drop-in replacement for the kit part and features a corrected nose profile, in particular around the upper lip where the small radome is located. The kit part is too blunt, in the same way as the FJ-2 part is. The panel l..

This is a cockpit set for Kitty Hawk's FJ-3 Fury kit (1:48). It includes a corrected and detailed seat with parachute and harness in place (which differs from the FJ-2 seat in several details), a detailed rear cockpit bulkhead and turtle deck, the FJ-3 specific antenna assembly (3D printed part) as ..

This is a replacement nose landing gear strut for Kitty Hawk's FJ-2 and FJ-3 Fury kits. It is 3D printed in one piece in strong resin and corrects the misshapen kit part. A lot of detail has been added and refined and as such the item is both a significant upgrade over the kit part as well as an evo..

This is a replacement nose landing gear strut for Kitty Hawk's FJ-2 and FJ-3 Fury kits. It is 3D printed in one piece in strong resin and corrects the misshapen kit part. A lot of detail has been added and refined and as such the item is both a significant upgrade over the kit part as well as an evo..

The set includes turned brass Pitot Tube, brass barrels and etched barrel clamps.It is very simple to use in Your model, cut off the original plastic barrel and drill a hole in the remaining plastic parts. Insert the metal barrel using Cyanoacrylate adhesives...

..

..

..

This is a set of small stabilators for Kinetic's F-16A and B models. The parts are the same as found in my F-16A Backdate Set (Block 1-10),so the stabilators themselves (cast in strong resin) plus the printed static dischargers. (No other parts are included)This set is very handy for example wit..

..

..

..

This is a drag chute compartment with dropped chute canister for any Kinetic F-104 Starfighter kits.Supplied will be both the empty, lowered canister with dropped retainer flap (for post-landing) as well as a canister stuffed with a packed chute and rased retainer flap...

A set of two Martin Baker Mk. H5 ejection seats for early F-4B, F-4C and F-4D Phantoms (until around 1970). Suitable for and tested with Academy, Hasegawa and Zoukei Mura kits. The seats have cast on seat belts which differ from each other...

..

Dassault Super Mystere B2 - Pitot Tubes (with resin mounts) & Angle Of Attack probes..

The set includes turned brass Pitot Tube. Fit to all 1:48 scale models of Mirage III and 5.It is very simple to use in Your model, and makes it extremely realistic. Insert the metal parts using Cyanoacrylate adhesives...

The set includes turned brass Pitot Tube and Angle Of Attack probe.Insert the metal parts using Cyanoacrylate adhesives. Drill proper hole in plastic part if needed...

This is an update set for ClearProp's D-21 kit. It contains more detailed and more accurate engine sets (with one-piece nozzle), intake with one-piece spike, new back plate and better proportioned pitot and a camera to go behind the glass...

This is a resin Canberra PR.9 and B(I)8 canopy in 1:48 scale with the correct circular cross section that replaces the Airfix canopy which has an incorrect "U" cross section. As the correct cross section is circular, the offset position makes it "tuck under" on the left side and that is not represen..