Flying Leathernecks

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 5.5 x 8.5 inch sheet..

Vinyl Mask..

Vinyl Mask..

This set contains pre-cut self adhesive vinyl Det Cords for the forward and aft canopies. Designed to fit the Kinetic / Wolfpack Design kits.Transfer tape included and pre-attached...

This set is designed to fit inside the kit and force the bottom seam into the proper position and allow easy gluing and seam work...

This set includes four (4) Mk-83 1000lb bombs with the Thermal Protective coating, four (4) Conical fins and four (4) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs.The Mk-83 was the weapon of choice for the USN and USMC during Operation Desert Storm and was used extensi..

Set of four (4) 3D printed launchersThe LAU-7F/A was first introduced in 2008, with more widespread use by 2010. This version is used primarily on USMC F/A-18C/D aircraft...

In January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6.Over the course of the next several years, numerous AAC's changed the designation of the launcher to B/A, A-7, B/A-1, as well as a few others. However, all of these changes were either..

Vinyl Mask..

3D ResinThis set includes the following items :Updated and Detailed Instrument Panel for BuNo's 163985 and Up Correct and Detailed WSO Instrument Panel for BuNo's 163986 and Up Correct WSO Instrument Panel Cover for the F/A-18D Left and Right side console WSO Control Sticks Rudder Pedals x 2 GPS A..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

3D ResinThis is a simple tool that can be used over and over.If built as designed, the vertical tails in the Hasegawa 1/48 Hornets angle too far out. This jig helps set them at the correct angle.Simply score (do not cut off) the outside surface of the locating tabs on the tail parts where it me..

This set includes correctly shaped and sized LEX Fence parts applicable to all 1/48 F/A-18A/B/C/D Hornet kits...

All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..

This set includes a total of four (4) tail stiffening plates commonly found on F/A-18A and F/A-18A+ Hornets. The four plates will complete two (2) models.3D printed, the plates have all of the rivet and screw fasteners visible. Simply remove from the support, sand the small attachment points smoot..

All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..

Set of 8 correctly sized and shaped pitot tubes for use on the Legacy F/A-18, F-14, A-7, F-8, AV-8B and several other aircraft that use this style of pitot tube.3D printed and lightly supported for easy removal from block...

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 5.5 x 8.5 inch sheet..

Vinyl Mask..

*Designed to be a drop in fit for the Hasegawa AV-8B series of kits. Simply paint and place in intake.* Some sanding may be required around the sides to get a proper fit.Master Patterns by Daniel Tompos..

Designed by Jason Liang, this new set corrects the horribly inaccurate TSS provided in the kit.Includes a holographic vinyl piece for the FLIR window. We recommend using a 5 minute epoxy, applied in thin layers to create the 'glass' for the TV windows...

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 5.5 x 8.5 inch sheet..

The FMV Mod fitted to the tail boom of the AH-1Z and UH-1Y allows grounds units to see what the aircrew sees through the aircraft's FLIR.Designed for the Kittyhawk kits..