Flying Leathernecks

3D ResinThis set includes two empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y, A-10, F-16 and a number of other aircraft.Pods are 3D printed and come ready to paint and attach t..

3D Resin..

3D ResinThis set contains two (2) LAU-10 5.00" rocket pods with empty tubes. Tubes are hollow the whole length of the pod.Designed by Matt Farrow of Shrunk Craft..

3D ResinThis set includes four (4) octagon shaped drip pans commonly found under aircraft, both on the flightline and in hangar spaces. Great for use in dioramas to add a little bit more realism to your scene.Parts come as shown in photo. Very light sanding needed on one surface needed prior to pa..

3D ResinThis set includes six (6) SATCOM Antenna with short mount found on a number of Helicopters. Use fine sprue cutters to remove part from support and lightly sand base smooth. Attach using super glue (CA)...

3D ResinAN/ALQ-144, ready to paint and attach to your model.For AH-1W, AH-64A/D/E, UH-1N, H-60, OH-58, VH-3D and OV-10..

3D ResinThis set includes 6 buckets that can be used to replace those found in kits that may be under detailed...

3D ResinThis set includes six (6) buckets that can be used in a diorama setting (ordnance loading evolution) or to replace kit parts...

Vinyl Detail..

3D ResinThis detailed TSS is a direct replacement for the kit parts. Simply detail paint and install.Use sprue cutters to remove turret from supports and lightly sand support nibs smooth. It may be necessary to remove the locating tabs from kit parts C59 and C60..

3D ResinThe FMV Mod fitted to the tail boom of the AH-1Z and UH-1Y allows grounds units to see what the aircrew sees through the aircraft's FLIR.Designed for the Academy kit..

3D ResinThis set includes four (4) ADU-299 Adapters. These are used to allow aircraft to carry the LAU-7 missile launcher on stations not normally designed to carry that launcher...

Cut in holographic vinyl to replicate the windows on the seeker head of the pod. Simply peel and stick after pod has been painted, decaled and weathered. Enough pieces for six pods are included.Designed for the pods included in the Academy F-16CG/CJ kit. Will work with other similar pods...

This set includes two (2) thermally protected Mk-83 1000lb bombs with conical fins and M904 nose fuses. 3D printed items come as shown in the photo...

This set includes two (2) thermally protected Mk-82 bombs with BSU-86 fins and MXU-735 Solid Nose Plugs3D printed items come as shown in the photo..

This set includes two (2) thermally protected Mk-82 bombs with BSU-86 fins and M904 fuzes3D printed items come as shown in the photo..

This set includes six (6) Mk-76 practice bombs..

This set includes two (2) LAU-7 launchers and is designed to be used with set FL18-1008 on the Hobbyboss AV-8B kit. Can also be used with the JSI 18th scale F-14 and F/A-18.Designed by Richard VanZandt..

This set includes eight (8) wing pylons, one (1) centerline pylons, two (2) aft pylon fairings, and seven (7) BRU-36 ejector racks.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..

This set contains two Mk-82/BLU-111/B Thermally Protected bombs, two MXU-735 solid nose plugs and two KMU-572 JDAM kits.For use with the Hobbyboss 1/18 AV-8B..

This set contains two Mk-82/BLU-111/B Thermally Protected bombs, two DSU-33 proximity fuzes and two KMU-572 JDAM kits.For use with the Hobbyboss 1/18 AV-8B..

Set includes two (2) Thermally Protected Mk-83/BLU-110 bombs with KMU-559 guidance kit attached and the tail assemblies as separate pieces. Also included are two (2) DSU-33 proximity fuzes...

Markings for two AV-8B II Plus HarriersVMA-542 Operation Iraqi Freedom 2008VMA-223 Operation Inherent Resolve 20158.5 x 11.0 inch sheet printed by Microscale.100% Made in the US..

This set includes six (6) wing pylons, two (2) centerline pylons, seven (7) BRU-36 ejector racks and two (2) adapters used when the LAU-7 missile launcher is attached to the outboard pylons.Different centerline pylons are configured for use with the strakes or gun pack.3D printed and designed b..